Contactez-nous

Chat en direct avec un représentant Tek. Service disponible de 6 h 00 à 16 h 30, PST.

Téléphone

Appelez-nous au 1-800-833-9200

Disponible de 9 h 00 à 17 h 00 (CET) jours ouvrables

Télécharger

Télécharger des manuels, des fiches techniques, des logiciels, etc. :

TYPE DE TÉLÉCHARGEMENT
MODÈLE OU MOT CLÉ

TSG130A

Analog Generator

The products on this datasheet are no longer being sold by Tektronix.
View Tektronix Encore for reconditioned test equipment.
Check support and warranty status for these products.

Lire en ligne :

Features & Benefits

  • Low Cost Test Signal Generator
  • Tailored to Service Applications
  • Supports Betacam, MII, S-VHS, Hi-8, GBR, and Composite Formats
  • BNC and S-connector Outputs
  • High Accuracy Test Signal Generation
  • Two Channels of Audio Tone With Channel One Identification
  • Compact and Lightweight
  • Black Burst Output (Option)
  • NTSC Test Signal Outputs

Applications

  • Component Analog Video Equipment Maintenance

The TSG130A is a low cost, multiformat test signal generator tailored for the testing and servicing of Betacam, MII, S-VHS, Hi-8, NTSC and 525/60 GBR video equipment. The 10-Bit digital signal generation and internal architecture allow generation of signals with the accuracy and stability until now available only in higher cost generators.

With the TSG130A, you get all the signals you need to test video levels, linearity, frequency response, phase response, clamp performance, chrominance noise, picture monitor alignment, inter-channel timing and more.

For convenience in servicing S-VHS and Hi-8 VCRs, the TSG130A provides the NTSC and Y/C outputs simultaneously, with the Y/C outputs available both from BNC connectors and the standard 4-Pin S-connector. Two channels of 1 kHz audio tone are provided on balanced XLR outputs. These phase locked tones are easily identified with the selectable ID pulse in channel one.

A dedicated black burst output is available as an option. This output is recommended for the service bench where an external reference signal is required for equipment fault diagnosis and adjustment.

All this comes in a package size small enough not to clutter the service bench. And for field servicing, the TSG130A fits nicely in a briefcase with the rest of the necessary service tools.

TSG130A Test Signals

Test Signal

NTSC & YC

Y, B-Y, R-Y

Y, CTDM

GBR

75% and 100% color bars

X

X

X

X

SMPTE color bars

X

   

   

   

Red, green, and blue fields

X

   

   

X

Flat fields 0, 50, 100%

X

X

X

   

Crosshatch

X

   

   

X

Chroma noise

X

   

   

   

Chroma response

X

   

   

   

Linearity:

5 step

X

Valid

   

X*1

Ramp

X

   

   

   

Mod ramp

X

   

   

   

Pulse & bar

X

X

   

X

Multiburst

X

X

   

X

Sweep

X

X

X

X

NTC 7 composite

X

   

   

   

Matrix

X

   

   

   

Bowtie

   

X

   

X

T Pulses

   

X

   

   

*1 Ten step.

Characteristics

391ill98-N

TSG130A rear panel.

(Standard and all Options)
NTSC, YC Test Signal Generator

Luminance Amplitude Accuracy - ±1%.

Chrominance Amplitude Accuracy (C Channel) - ±1%.

Chrominance-to-luminance Gain - ±1%.

Chrominance-to-luminance Delay - ≤15 ns.

Frequency Response - ±2% to 4.2 MHz (NTSC output); ±1% to 5 MHz, ±2% to 5.5 MHz (all other outputs).

SCH Phase Accuracy - 0° ±5°.

Line Blanking Interval - 10.9 µs ±0.2 µs.

Output Impedance - 75 Ω.

Component Test Signal Generator

Amplitude -

Accuracy: ±1%.

Channel to channel match: ±0.5% B-Y and R-Y relative to Y.

Frequency Response -

Y Channel: ±1% to 5 MHz, ±2% to 5.5 MHz.

B-Y, R-Y Channels: ±1% to 2.75 MHz.

Channel-to-channel Timing Match - Within 5 ns; B-Y and R-Y relative to Y.

Sync Amplitude -

Betacam: 285.7 mV.

MII: 300 mV.

Blanking Width - 10.9 ±0.2 µs.

Output Impedance - 75 Ω.

Internal Reference

Frequency - 3.579545 MHz.

Stability Over Temperature - Within 10 Hz from 5 °C to 35 °C.

Audio Tone Generator

Frequency - 1 kHz.

Amplitude - 0 to +8 dBu into 600 Ω or a high impedance load.

Distortion - ≤0.5% THD + N.

Click ID - Rate adjustable from 0.2 Hz to 4 Hz.

Power Source

Mains -

Voltage range: 90-130 VAC; 180-250 VAC.

Frequency range: 48-62 Hz.

Power Consumption - 15 W typical.

Environmental

Temperature -

Operating: 0 °C to +35 °C.

Nonoperating: -40 °C to +65 °C.

Certifications

EMC - Certified to the EMC Directive 89/336/EEC.

Safety - Approved to: UL1244, CSA231.

Complies with: EN61010-1, IEC61010-1.

Physical Characteristics

Dimensions

mm

in.

Weight

kg

lb.

Width

205.7

8.1

Height

43.4

1.71

Depth

381

15

Net

1.47

3.25

Shipping

3.2

7.06

Ordering Information

TSG130A

Multiformat Signal Generator.

Note: - Only options 01 and 02 may be combined.

Opt. 01 - MII test signals (Replaces Betacam Signals).

Opt. 02 - Adds a dedicated black burst output.

Opt. 2J - 0 IRE setup and black burst.

Opt. 03 - Sony PVW Series Service (Includes a special test signal set, black burst output, and TTL level color frame pulse output).

Opt. 04 - Panasonic MII Service (Includes a special test signal set and TTL level comp sync and frame pulse outputs).

Opt. 05 - Add DVCPRO Service Test Signals.

Optional Accessories

Mounting Kits -

Hardware to mount any one of TSG100 Series, ASG100 or VITS100 products in a one rack unit high space. Order TVGF11A.

Hardware to mount any two of TSG100 Series, ASG100 and VITS100 products side-by-side in a two rack unit high space. Order TVGF13.

Hardware to mount any two of TSG100 Series, ASG100 and VITS100 products vertically in one-half of a WFM7F05 rack adapter. Order TVGF14.

Service

Opt. C3 - Calibration Service 3 Years

Opt. C5 - Calibration Service 5 Years

Opt. D1 - Calibration Data Report

Opt. D3 - Calibration Data Report 3 Years (with Option C3)

Opt. D5 - Calibration Data Report 5 Years (with Option C5)

Opt. R3 - Repair Service 3 Years

Opt. R5 - Repair Service 5 Years