TLA7Dx/Ex Digital Storage Oscilloscope Modules

Tektronix Logic Analyzers
Les produits decette fiche technique ne sont plus commercialisés par Tektronix.

Lire en ligne :

Features & Benefits

  • 2/4 Channel Digitizing Oscilloscope Modules with 15 Kb Memory Depth
  • Up to 1 GHz Bandwidth Provides High-fidelity Signal Quality Measurements of Digital Signals
  • Up to 5 GS/s Sample Rate Provides High Resolution Analog Views of Digital Signals
  • Advanced Digital Oscilloscope Triggering Helps Find Elusive Analog Anomalies in Digital Signals


  • Digital Hardware Verification and Debug
  • Monitor & Measure Digital Hardware Performance

Breakthrough Solutions for Real-time Digital Systems Analysis

The TLA700 Series offers a range of digitizing oscilloscope modules that provide the acquisition capabilities of the world's best digitizing oscilloscopes, tightly integrated with the TLA700 logic analyzers. The 2 and 4 channel digitizing oscilloscope modules available in the TLA700 Series offer sample rates of up to 5 GS/s and bandwidths of up to 1 GHz, with 15 Kb memory depth per channel at all times.

The digitizing oscilloscope modules offer precise time correlation and flexible cross-triggering with other installed modules. This enables you to see the quality of critical signals time-correlated with the digital signals represented by the logic analyzer modules.

These modules offer the triggering you expect from a Tektronix digital oscilloscope: Pulse Width, Runt, Glitch, Slew Rate, Logic Pattern, Setup-and-Hold Violation, Edge and Timeout.



Number of Channels per Module -

TLA7E2: 4 channels.

TLA7D1: 2 channels.

Sample Rate -

TLA7E2: 5 GS/s on all channels.

TLA7D1: 2.5 GS/s on all channels.

Bandwidth (at probe tips) -


100 mV to 10 V range: 1 GHz.

50 mV to 99.8 mV range: 900 MHz.

20 mV to 49.8 mV range: 600 MHz.


500 MHz on all channels in all ranges.

Memory Depth - 15,000 samples per channel in all modes.

Number of Mainframe Slots Required -  2.

Vertical System

Input Sensitivity Range - 10 mV to 100 V full scale.

Vertical Resolution - 8-Bit (256 levels).

DC Gain Accuracy - ±1.5% of full scale range.

Analog Bandwidth Selections - 20 MHz, 250 MHz, and Full.

Input Coupling - AC, DC or GND.

Input Impedance Selections - 1 MΩ in parallel with 10 pF, or 50 Ω.

AC Coupled Lower Frequency Limit - ≤10 Hz when AC 1 MΩ coupled, ≤200 kHz when AC 50 Ω coupled.

Maximum Input Voltage at Probe Connector - 300 VRMS, but no greater than ±420 Vp (1 MΩ or ground input coupling).

Probe Input Characteristics

Probe Input Interface - TEKPROBE™ probe interface.

Input Loading - Less than 1 pF in parallel with 1 MΩ with either P6243 or P6245.

Usable Input Voltage Range at Probe Tip - P6243 Probe: ±8 V. P6245 Probe: ±18 V.

Acquisition System

Sample Rate Range - 200 ps to 200 ms in 1, 2.5, 5 sequence.

Timebase Accuracy - ±100 ppm over any interval ≥1 ms.

Record Length Range - 512 to 15,000 samples per channel in all modes.

Acquisition Modes - Single-shot, repetitive.

Trigger System

Trigger Modes - Normal, auto.

Trigger Position - Anywhere in the acquired record (pre-fill can be set anywhere from 0% to 100%).

Trigger Types - Edge, pulse width, timeout, glitch, runt, slew rate, logic pattern, setup-and-hold violation.

Trigger Actions - Trigger, trigger all, set signal, arm, immediate, wait for system trigger.

Edge Trigger - Conventional level driven trigger, positive or negative slope, on any channel or external trigger input. Coupling Selections: DC, AC, noise reject, HF reject, LF reject.


Edge trigger.

Pulse Width Trigger - Triggers on width of positive or negative pulse, either within or not within selectable time limits; settable from 2 ns to 1 s.


Pulse Width trigger.

Timeout Trigger - Triggers when a pulse fails to complete when specified; settable from 2 ns to 1 s.


Timeout trigger.

Glitch Trigger - Triggers on (or rejects) glitches of positive, negative, or either polarity; settable from 2 ns to 1 s. Minimum glitch width: 2.0 ns, with 200 ps resolution (2 ns to 10 ns settings).


Glitch trigger.

Runt Pulse Trigger - Triggers on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again; settable from 2 ns to 1 s.


Runt Pulse trigger.

Slew Rate Trigger - Triggers on pulse edge rates that are either faster or slower than a set rate, edges can be rising, falling, or either; settable from 2 ns to 1 s.


Slew Rate trigger.

Logic Pattern Trigger - Triggers when a logical combination (AND, OR) of all the input channels (Hi, Lo, Don't Care) stays true or false for a specified period of time; settable from 2 ns to 1 s.


Logic Pattern trigger.

Setup-and-hold Trigger - Triggers on violations of both setup time and hold time between clock and data which are on separate input channels; setup time settable from -100 ns to +100 ns in 200 ps increments; hold time settable from -1 ns to +102 ns; minimum settable window of setup time + hold time is 2 ns.


Setup-and-hold trigger.

Safety - CSA C22.2 No. 1010.1, EN61010-1, IEC61010-1, UL 3111-1.


Physical Characteristics






















P6243 Probe Cable Length - 1.3 m (51 in.).

P6245 Probe Cable Length - 1.3 m (51 in.).

Last Modified: 2002-12-01 04:00:00

Télécharger des manuels, des fiches techniques, des logiciels, etc. :

Go to top