Télécharger
Télécharger

Télécharger des manuels, des fiches techniques, des logiciels, etc. :

TYPE DE TÉLÉCHARGEMENT
MODÈLE OU MOT CLÉ

3 Series MDO, 4/5/6 Series MSO Applications Datasheet

Serial Triggering and Analysis

Lire en ligne :

On a serial bus, a single signal often includes address, control, data, and clock information. This can make isolating events of interest difficult. Optional serial applications transform the oscilloscope into a robust tool for debugging serial buses with automatic decode and analysis for I2C, SPI, CAN, CAN FD, LIN, FlexRay, 100BASE-T1, SENT, RS-232/422/485, UART, USB 2.0 (LS, FS, HS), Ethernet, I3C, SPMI, Spacewire, 8b10b, NRZ, MIL-STD-1553, ARINC 429, I2S, LJ, RJ, PSI5 and TDM.

Key features
  • Automated Serial Decode and Analysis Options for I2C, SPI, I3C1, CAN, CAN FD, LIN, FlexRay, SENT1, RS-232/422/485, UART, USB 2.0, Ethernet1, SPMI1, MIL-STD-1553, ARINC 429, I2S, LJ, RJ, PSI5 and TDM

  • Trigger on all the critical elements of a serial bus such as address, data, etc.
  • Decode all the critical elements of each message. No more counting 1s and 0s!
  • Search through long acquisitions with user-defined criteria to find specific messages
  • Event Table shows decoded serial bus activity in a tabular, time-stamped format for quick summary of system activity

1Not available for 3 Series MDO.

Serial Triggering and Analysis Applications

The serial applications support automatic trigger and decode for I2C, SPI, CAN, CAN FD, LIN, FlexRay, 100BASE-T1, SENT, RS-232/422/485, UART, USB 2.0 (LS, FS, HS), Ethernet, I3C, SPMI, Spacewire, 8b10b, NRZ, MIL-STD-1553, ARINC 429, I2S, LJ, RJ, PSI5 and TDM buses, making it easier to locate, analyze, and debug events of interest.

Serial triggering

Trigger on packet content such as start of packet, specific addresses, specific data content, unique identifiers, etc. on popular serial interfaces such as I2C, SPI, CAN, CAN FD, LIN, FlexRay, SENT, RS-232/422/485, UART, USB 2.0, Ethernet, SPMI, MIL-STD-1553, ARINC 429, I2S, LJ, RJ, PSI5 and TDM.

Bus display

The bus display provides a higher-level, combined view of the individual signals (clock, data, chip enable, and so on) that make up your bus, making it easy to identify where packets begin and end and identifying sub-packet components such as address, data, errors, and so on.

Bus decoding

Tired of having to visually inspect the waveform to count clocks, determine if each bit is a 1 or a 0, combine bits into bytes, and determine the hex value?

Let the oscilloscope with a serial application do it for you! Once you've set up a bus, the oscilloscope decodes each packet on the bus, and displays the value in hex, binary, ASCII, or decimal (certain buses only) in the bus waveform.

Results table

In addition to seeing decoded packet data on the bus waveform itself, you can view all captured packets in a tabular view much like you would see in a software listing. Packets are time stamped and listed consecutively with columns for each component (Address, Data, and so on).

Wave Inspector®search

Serial triggering is very useful for isolating the event of interest, but once you've captured it and need to analyze the surrounding data, what do you do?

In the past, users had to manually scroll through the waveform counting and converting bits and looking for what caused the event. With a serial application, you can enable the oscilloscope to automatically search through the acquired data for user-defined criteria including serial packet content. Each occurrence is highlighted by a search mark. Rapid navigation between marks is as simple as pressing the ← and → arrow buttons on the oscilloscope front panel or the Search badge. The 3 Series MDO uses the arrows in the Search badge to navigate.

Characteristics

I2C characteristics
Bus setup options
Characteristic Description
I2C Sources
(Clock and Data)
Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Thresholds Per-channel thresholds
Recommended Probing Single-ended
Include R/W in Address Yes or No
Address/Data Formats Available Hex
Binary

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Start
Repeated Start
Stop
Missing Ack
Address (7 or 10 bit)
Data (1-5 bytes)
Address and Data

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 10 Mb/s (automatic selection)
Decode Display Start (green bar)
Address (yellow packet)
Data (cyan packet)
Missing Ack (! symbol in red box)
Stop (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific address value on the I2C bus.

1Not available on 3 Series MDO

SPI characteristics
Bus setup options
Characteristic Description
SPI Sources (Clock, Data, and Slave Select) Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Thresholds Per-channel thresholds
Recommended Probing Single-ended
Decode Configuration: Framing
Clock
Slave Select
Data
Word Size
Bit Order
 
Slave Select (3-wire SPI), Idle Time (2-wire SPI)
Rising or Falling Edge
Active High or Active Low
Active High or Active Low
4 - 32 bits
Most Significant (MS) First, Least Significant (LS) First
Formats Available Hex
Binary

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On SS Active (3-wire SPI)
Start of Frame (2-wire SPI)
Data (1-16 bytes)

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 10 Mb/s (automatic selection)
Decode Display Start (green bar)
Data (cyan packet)
Stop (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
SPI bus, captured with digital channels, showing binary display format of the color-coded SPI bus decoding.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific data value on the SPI bus.

1Not available on 3 Series MDO.

I3C characteristics1
Bus setup options
Characteristic Description
I3C Sources
(Clock and Data)
Analog channels
Digital channels
Active Math channels
Active Reference channels
Thresholds Per-channel thresholds
Speed High Speed (480 Mb/s)
Full Speed (12 Mb/s)
Low Speed (1.5 Mb/s)
Recommended Probing Single-ended
Formats Available Hex
Binary
Mixed Hex

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus search options
Characteristic Description
Search On Start
Repeated Start
Address
Data
I3C SDR Direct Message
I3C SDR Broadcast Message
I3C DDR Message
Errors
Hot-Join
Direct Message End
Stop
HDR Restart
HDR Exit

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 12.5 Mb/s (automatic selection)
Decode Display Start (green bar)
Address (yellow packet)
Commands (cyan packet)
Data (cyan packet)
Parity (purple packet)
Stop (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Searching on a specific data pattern on the I3C bus and automatically searching on Sync.

1I3C is not available on 3 Series MDO.

RS-232, RS-422, RS-485, UART characteristics
Bus setup options
Characteristic Description
Sources, RS-232, UART Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Sources, RS-422, RS-485  Analog channels
Active Math channels1
Active Reference channels1
Polarity Normal (RS-232)
Inverted (UART, RS-422, RS-485)
Parity None
Odd
Even
Recommended Probing, RS-232, UART Single-ended
Recommended Probing, RS-422, RS-485  Differential
Number of Bits 7 - 9 
Formats Available Hex
Binary
ASCII
Packet View

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Start
End of Packet
Data (1 - 10 bytes)
Parity Error

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 15 Mb/s For 3 Series MDO: Up to 10 Mb/s
Bit Rate Selection 300 b/s
1,200 b/s
2,400 b/s
9,600 b/s
19,200 b/s
38,400 b/s
115,200 b/s
921,600 b/s
Custom (All but 3 Series MDO: 50 b/s - 15 Mb/s
Custom (for 3 Series MDO): 50 b/s - 10 Mb/s
Decode Display Start (green packet)
Data (cyan packet)
Parity (purple packet)
Parity Error (red packet)


3 4 5 6Series MSO Serial Bus Analysis Datasheet
RS-232 bus setup and ASCII display, showing assignment of source signal, digital threshold, and polarity.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
RS-232 bus shown in Packet View format, with the Wave Inspector search automatically searching for the data string "Tek".

1Not available on 3 Series MDO.

CAN characteristics
Bus setup options
Characteristic Description
Source for CAN_H, CAN_L, Rx, or Tx (single-ended probing) Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Source for Diff (differential probing) Analog channels
Active Math channels1
Active Reference channels1
Thresholds Per-channel thresholds
Recommended Probing: CAN_H, CAN_L, Rx, Tx
Diff
 
Single-ended
Differential
Bit Rate Selection: Predefined list of rates
 
Custom
 
10 kb/s - 1 Mb/s
 
All but 3 Series MDO: 1 kb/s - 1 Mb/s
3 Series MDO: 10 kb/s - 1 Mb/s
Sample Point All but 3 Series MDO: 0% - 100% of bit period of unit interval
3 Series MDO: 5% - 95% of bit period of unit interval
Formats Available Mixed Hex
Hex
Binary
Symbolic (.dbc)1
Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view
Bus trigger and search options
Characteristic Description
Trigger and/or Search On Start of Frame
Type of Frame (Data, Remote, Error, Overload)
Identifier (Standard or Extended)
Data (number of bytes 1-8, trigger or search when =, ≠, <, ≤, >, ≥)
Identifier and Data
EOF
Missing Ack
Bit Stuff Error
Symbolic bus search options
Characteristic Description
Message As defined by the .dbc file1
Message and Signal As defined by the .dbc file1
Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 1 Mb/s (automatic selection)
Decode Display Start of Frame (green bar)
Identifier (yellow packet)
Data Length Control (purple packet)
Data (cyan packet)
CRC (purple packet)
End of Frame (red bar)
Errors (red packet)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the CAN bus.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific extended Identifier value on the CAN bus.

1Not available on 3 Series MDO.

CAN FD (ISO and non-ISO) characteristics
Bus setup options
Characteristic Description
Source for CAN_H, CAN_L, Rx, or Tx
(single-ended probing)
Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Source for Diff
(differential probing)
Analog channels
Active Math channels1
Active Reference channels1
Thresholds Per-channel thresholds
Recommended Probing:
CAN_H, CAN_L, Rx, or Tx Diff
 
Single -ended
Differential
Version ISO
non-ISO
SD Bit Rate Selection:
Predefined list of rates
Custom
 
10 kb/s - 1 Mb/s
All but 3 Series MDO: 50 kb/s - 10 Mb/s
3 Series MDO: 10 kb/s - 1 Mb/s
FD Bit Rate Selection:
Predefined list of rates
 
Custom
 
All but 3 Series MDO: 1 Mb/s - 16 Mb/s
3 Series MDO: 1 Mb/s - 7 Mb/s
All but 3 Series MDO: 500 kb/s - 16 Mb/s
3 Series MDO: 500 kb/s - 7 Mb/s
Sample Point All but 3 Series MDO: 55% - 95% of bit period of unit interval
3 Series MDO: 15% - 95% of bit period of unit interval
Formats Available Mixed Hex
Hex
Binary
Symbolic (.dbc)1

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Start of Frame
Type of Frame (Data, Remote, Error, Overload)
FD Bits (Bit Rate Switch bit, Error State Indicator bit)
Identifier (Standard or Extended)
Data (1-8 bytes, trigger or search when =, ≠, <, ≤, >, ≥)
Identifier and Data
End of Frame
Error (Missing Ack, Bit Stuffing Error, FD Form Error, Any Error)

 

Symbolic bus search options
Characteristic Description
Message As defined by the .dbc file1
Message and Signal As defined by the .dbc file1

 

Bus decode
Characteristic Description
Decode Display Start of Frame (green bar)
Identifier (yellow packet)
Data Length Control (purple packet)
Data (cyan packet)
CRC (purple packet)
End of Frame (red bar)
Errors (red packet)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the CAN FD bus.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific Identifier value and data pattern on the CAN FD bus and automatically searching on the same data pattern.

1Not available on 3 Series MDO.

LIN characteristics
Bus setup options
Characteristic Description
LIN Source Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Thresholds Per-channel thresholds
Recommended Probing Single-ended
Polarity Normal
Inverted
Bit Rate Selection: Predefined list of rates
Custom
 
1.2 kb/s - 19.2 kb/s
All but 3 Series MDO: 1 kb/s - 100 kb/s
3 Series MDO: 800 b/s - 100 kb/s
Sample Point All but 3 Series MDO: 0% - 100% of bit period of unit interval
3 Series MDO: 10% - 90% of bit period of unit interval
LIN Standard V 1.x
V 2.x
Both
Include Parity Bits with ID Yes
No
Formats Available Hex
Binary
Mixed

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Sync
Identifier
Data (number of bytes 1-8, trigger or search when =, ≠, <, ≤, >, ≥, Inside Range, Outside Range)
ID and Data
Wakeup Frame
Sleep Frame
Error (Sync, ID Parity, Checksum)

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 100 kb/s, by LIN definition up to 20 kb/s (for automated decoding of bus)
Decode Display Start of Frame (green bar)
Sync
Identifier (yellow packet)
Data (cyan packet)
CRC (purple packet)
Errors (red packet)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured LIN packets.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Display of multiple LIN and CAN buses, showing timing between the buses.

1Not available on 3 Series MDO.

FlexRay characteristics
Bus setup options
Characteristic Description
Source for Differential Probing (Bdiff) Analog channels
Active Math channels 1
Active Reference channels1
Source for Single-ended Probing (BP, BM) Analog channels
Digital channels
Active Math channels1
Active Reference channels1
Source for Single-ended Probing (Tx, Rx) Analog channels
Digital channels
Active Math channels1
Active Reference channels1
Thresholds: Bdiff
BP, BM (analog channels)
BP, BM (digital channels)
Tx, Rx
 
High and Low thresholds
High and Low thresholds
Single threshold
Single threshold
Recommended Probing: Bdiff, BP, BM
Tx, Rx
 
Differential
Single-ended
Channel Type A
B
Bit Rate Selection: Predefined list of rates
Custom
 
2.5 Mb/s, 5 Mb/s, 10 Mb/s
1 Mb/s - 10 Mb/s
Formats Available Hex
Binary
Mixed Hex (Decimal: ID, Len, and Count; Hex: Data and CRCs)

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Start of Frame
Indicator Bits (Normal, Payload, Null, Sync, Startup)
Cycle Count (when =, ≠, <, ≤, >, ≥)
Header Fields (Indicator Bits, Identifier, Payload Length, Header CRC, and Cycle Count)
Identifier (when =, ≠, <, ≤, >, ≥)
Data (when =, ≠, <, >, ≤, ≥)
Identifier and Data
End Of Frame (Static, Dynamic)
Error (Header CRC, Trailer CRC, NULL Frame in Static, NULL Frame in Dynamic, Sync Frame in Dynamic, Start Frame No Sync)

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 10 Mb/s (for automated decoding of bus)
Decode Display TTS (purple box)
Start (green bracket)
Frame ID (yellow box)
Payload Length (purple box)
Headers (purple box)
Cycle Count (yellow box)
Data (cyan box)
CRC, DTS, CID (purple box)
Stop (red bracket)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Decoded FlexRay bus, with the acquisition triggered on a specified identifier value.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Decoded FlexRay bus, with all data values in a specific range marked with pink brackets.

1Not available on 3 Series MDO.

SENT Characteristics1

 

Bus setup options
Characteristic Description
SENT source Analog channels
Digital channels
Active Math channels
Active Reference channels
Thresholds Per-channel thresholds
Recommended Probing Single-ended
Polarity Normal
Inverted
Clock Tick 1 μs - 300 μs
Tick Tolerance 1% - 30%
Fast Data Channels 1 or 2 
Data Nibbles (1 Fast Data Channel) 3, 4, or 6 nibbles
Channel Widths (C1/C2) (2 Fast Data Channels) 12/12, 14/10, or 16/8 bits
Pause Pulse Yes
No
Slow Channel None
Enhanced w/ 4-bit ID
Enhanced w/ 8-bit ID
Short
Formats Available Mixed Hex
Binary
Hex
Mixed Decimal

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger options
Characteristic Description
Trigger On Start of Packet
Fast Channel(s) (Status/Communication, Data)
Slow Channel (Message ID, Data)
CRC Error (Fast channel, Slow channel)

 

Bus search options
Characteristic Description
Search On Start of Packet
Fast Channel(s) (Status/Communication, Data)
Slow Channel (Message ID, Data)
Pause Pulse (Number of Ticks)
Error (Frame Length, Fast channel CRC, Slow channel CRC)

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 10 Mb/s (for automated decoding of bus)
Decode Display Sync (green packet)
Fast Channel Status (purple packet)
Slow Channel Message ID (yellow packet)
Data (cyan packet)
CRC (purple packet)
Pause (purple packet)
Errors (red packet)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the SENT bus.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific Fast Channel Status and data pattern on the SENT bus and automatically searching on the same data pattern.

1SENT is not available on 3 Series MDO.

MIL-STD-1553 characteristics
Bus setup options
Characteristic Description
MIL-STD-1553 Source Analog channels
Active Math channels
Active Reference channels
Polarity Normal
Inverted
Thresholds Single-ended: Per-channel thresholds
Differential: High and low thresholds
Recommended Probing Single-ended or differential
Bit Rate 1 Mb/s per the standard
Response Time 2 µs-100 µs
Formats Available Mixed Hex
Mixed ASCII
Hex
Binary

 

Display modes
Characteristic Description
Bus Bus only
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Sync
Command (Transmit/Receive Bit, Parity, Subaddress / Mode, Word Count / Mode Count, and RT Address =, ≠, <, ≤, >, ≥, Inside Range, Outside Range)
Status (Parity,
  Bit 9 - Message Error,
  Bit 10 - Instrumentation,
  Bit 11 - Service Request,
  Bit 15 - Broadcast Command Received,
  Bit 16 - Busy,
  Bit 17 - Subsystem Flag,
  Bit 18 - Dynamic Bus Control Acceptance,
  Bit 19 - Terminal Flag,
  and Data =, ≠, <, ≤, >, ≥,
  Inside Range, Outside Range)
Data (Parity, and Data =, ≠, <, ≤, >, ≥,
  Inside Range, Outside Range)
Time (RT / IMG) (> Maximum, < Minimum, Inside range, Outside Range)
Error (Parity Error, Sync Error, Manchester Error (trigger only), Non-contiguous Data)

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate Up to 1Mb/s (for automated decoding of bus)
Decode Display Start (green bar)
Sync (purple packet with Word Type identified)
Address (yellow packet)
R/T (purple packet)
Word Count (purple packet)
Data (cyan packet)
Parity (purple packet)
Errors (red packet)
Stop (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured MIL-STD-1553 packets.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific command pattern on the MIL-STD-1553 bus and automatically searching on the same pattern.

ARINC 429 characteristics
Bus setup options
Characteristic Description
ARINC 429 Source Analog channels
Active Math channels
Active Reference channels
Signal Type Differential
Polarity Normal
Inverted
Thresholds High and low thresholds
Recommended Probing Differential
Bit Rate Selection:
  Predefined list of rates
  Custom
 
12.5 kb/s, 100 kb/s
10 kb/s - 1 Mb/s
Data Format Data (19 bits)
SDI+Data (21 bits)
SDI+Data+SSM (23 bits)
Formats Available Mixed Hex
Hex
Binary

 

Display modes
Characteristic Description
Bus Bus only
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Word Start
Label (when =, ≠, <, ≤, >, ≥, Inside Range, Outside Range)
Data (when =, ≠, <, ≤, >, ≥, Inside Range, Outside Range)
Label and Data (Label value and Data =, ≠, <, ≤, >, ≥, Inside Range, Outside Range)
Word End
Error (Any Error, Parity Error, Word Error, Gap Error)

 

Bus decode
Characteristic Description
Decode Display Start (green bracket)
Label (yellow box)
Source Destination Identifier (yellow box)
Data (cyan box)
Sign/Status Matrix (purple box)
Parity (purple box)
Stop (red bracket)
Error (red box)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Decoded ARINC 429 bus, with the acquisition triggered on a specified label value.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Decoded ARINC 429 bus, with all data values in a specific range marked with pink brackets.

Audio characteristics
Bus setup options
Characteristic Description
Audio Sources (Bit Clock, Word Select, Data) Analog channels
Digital channels
Active Math channels 1
Active Reference channels1
Thresholds Per-channel thresholds
Bit Clock Polarity Rising Edge
Falling Edge
Word Select Polarity Normal
Invert
Data Polarity Active High
Active Low
Word Size 4 - 32 bits
Formats Available Hex
Binary
Signed Decimal

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger and search options
Characteristic Description
Trigger and/or Search On Word Select (I2S, LJ, RJ only)
Frame Sync (TDM only)
Data (when =, ≠, <, >, ≤, ≥, Inside Range, Outside Range; Left, Right, or Either Word)

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate All but 3 Series MDO: Up to 10 Mb/s (for automated decoding of bus)
3 Series MDO: Up to 12.5 Mb/s (for automated decoding of I2S/LJ/RJ bus)
3 Series MDO: Up to 25 Mb/s (for automated decoding of TDM bus)
Decode Display Left Channel Data (I2S, LJ, RJ) (yellow box)
Right Channel Data (I2S, LJ, RJ) (cyan box)
Channel 1 Data (TDM) (yellow box)
Channel 2 - N Data (TDM) (cyan box)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Decoded I2S bus, with data values displayed in signed decimal format, and the MSO triggered on a specific data value.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Decoded I2S bus, with data values displayed in hex and Results Table format, and the Wave Inspector automatic search marking all occurrences of the data values equal to 0X hex.

1Not available on 3 Series MDO.

USB 2.0 Characteristics
Bus setup options
Characteristic Description
USB 2.0 Source(s) Analog channels
Digital channels (single-ended)
Active Math channels
Active Reference channels
Thresholds Per-channel thresholds
Speed High Speed (480 Mb/s)
Full Speed (12 Mb/s)
Low Speed (1.5 Mb/s)
Recommended Probing, LS and FS Single-ended
Recommended Probing, HS Differential
Formats Available Mixed Hex
Hex
Binary
Mixed ASCII

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger options
Characteristic Description
Trigger On Sync
Reset
Suspend
Resume
End of Packet
Token (address) Packet
Data Packet
Handshake Packet: ACK, NAK, STALL, NYET (HS only)
Special Packet: PRE (FS only), ERR, SPLIT, PING, Reserved
Error: PID check, CRC5 or CRC16, Bit stuffing (LS and FS only)

 

Bus Search options
Characteristic Description
Search On Sync
Reset
Suspend
Resume
End of Packet
Token (address) Packet
Data Packet
Handshake Packet: ACK, NAK, STALL, NYET (HS only)
Special Packet: PRE (FS only), ERR, SPLIT, PING, Reserved
Error: PID check, CRC5 or CRC16, Bit stuffing (LS and FS only)

 

Bus decode
Characteristic Description
Decode Display Start of packet (green bar)
Sync (green packet)
PID (yellow packet)
Token (address) (yellow packet)
Data (cyan packet)
CRC (purple packet)
Error (red packet)
End of packet (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the USB bus.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering on a specific data pattern on the USB 2.0 bus and automatically searching on Sync.

Ethernet characteristics1
Bus setup options
Characteristic Description
Ethernet Source(s) Analog channels
Active Math channels
Active Reference channels
Thresholds Per-channel thresholds
Speed 10BASE-T
100BASE-TX
Recommended Probing Differential
Formats Available Mixed Hex
Hex
Binary
Mixed ASCII

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger options
Characteristic Description
Trigger On Start Frame Delimiter
MAC Addresses
Q-Tag Control Information
MAC Length/Type
IPv4 Header
TCP Header
MAC Data
TCP-IPv4 Client Data
Idle
End of Packet
Frame Check Sequence (CRC) Error

 

Bus search options
Characteristic Description
Search On Start Frame Delimiter
MAC Addresses
Q-Tag Control Information
MAC Length/Type
IPv4 Header
TCP Header
MAC Data
TCP-IPv4 Client Data
Idle
End of Packet
Frame Check Sequence (CRC) Error

 

Bus decode
Characteristic Description
Decode Display Start of Packet (green bar)
Preamble (purple packet)
SFD (purple packet)
Address (yellow packet)
EtherType (yellow packet)
IP packet (purple packet)
Data (cyan packet)
IPv4 packet (pink packet)
TCP packet (white packet)
Frame Check Sequence (yellow packet)
Error (red packet)
End of packet (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the 10BASE-T Ethernet bus

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Triggering and automatically searching on the 100BASE-TX Ethernet bus.

1Ethernet is not available on 3 Series MDO.

SPMI characteristics1
Bus setup options
Characteristic Description
SPMI Sources (Clock and Data) Analog channels
Digital channels
Active Math channels
Active Reference channels
Thresholds Per-channel thresholds
Recommended Probing Single-ended
Formats Available Mixed Hex
Hex
Binary

 

Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus trigger options
Characteristic Description
Trigger On Sequence Start Condition (SSC)
Reset
Sleep
Shutdown
Wakeup
Authenticate
Master Read
Master Write
Register Read
Register Write
Extended Register Read
Extended Register Write
Extended Register Read Long
Extended Register Write Long
Device Descriptor Block Master Read
Device Descriptor Block Slave Read
Register 0 Write
Transfer Bus Ownership
Parity Error

 

Bus search options
Characteristic Description
Search On Sequence Start Condition (SSC)
Reset
Sleep
Shutdown
Wakeup
Authenticate
Master Read
Master Write
Register Read
Register Write
Extended Register Read
Extended Register Write
Extended Register Read Long
Extended Register Write Long
Device Descriptor Block Master Read
Device Descriptor Block Slave Read
Register 0 Write
Transfer Bus Ownership
Parity Error

 

Bus decode
Characteristic Description
Decode Display Arbitration Start (yellow bar)
Connect Bit (purple packet)
Master ID (purple packet)
Alert Bit (yellow packet)
Slave Request Bit (yellow packet)
Master Priority Level (gray packet)
SSC (green bar)
Command Frame, including Byte Count 2 (yellow packet)
Address (yellow packet)
Data (cyan packet)
Parity (purple packet)
Ack/Nack (purple packet)
Parity error (red packet)
End of packet (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the SPMI bus.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Automatically searching the SPMI bus for the Transfer Bus Ownership command

1SPMI is not available on 3 Series MDO.

2The actual decimal Byte Count is displayed in Mixed Hex format, but the raw value is shown in Binary and Hex formats.

SpaceWire characteristics
Bus setup options
Characteristic Description
SpaceWire Sources
(Strobe and Data)
Analog Channels
Digital Channels
Active Math Channels
Active Reference Channels
Thresholds Per-Channel Thresholds
Recommended Probing Differential
Address/Data Formats Available Hex
Binary

 

Display modes
Characteristic Description
Bus Bus Only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus search options
Characteristic Description
Search On Synchronization
Control Code
Control Character
Data
Errors

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate 2 Mbits/sec to 200 Mbits/sec
Decode Display Null
Control Character
Control Code
FCT
Time-Code
Parity
Data-Control Flag
Data
End Of Packet
Error End Of Packet
Escape Sequence
Escape Error
Start FCT
Start NULL

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Searching on a specific data pattern on the SpaceWire bus and automatically searching on Sync.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
The Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the SpaceWire bus.

Automotive Ethernet (100BASE-T1) characteristics
Bus setup options
Characteristic Description
Ethernet Source(s) Analog Channels
Active Math Channels
Active Reference Channels
Thresholds Per-channel Thresholds
Speed 100 Mbits/sec
Recommended Probing Differential
Formats Available Mixed Hex
Hex
Binary
Mixed ASCII

 

Display modes
Characteristic Description
Bus Bus Only
Results Table Decoded packet data in a tabular view

 

Bus search options
Characteristic Description
Search On Start of Frame
Start of Frame Delimiter
MAC Addresses
Q-Tag Control Information
MAC Length/Type
IPv4 Header
TCP Header
MAC Data
TCP-IPv4 Client Data
End of Packet
Frame Check Sequence (CRC) Error

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate 100 Mbits/sec
Decode Display Start of Packet (green bar)
Preamble (purple packet)
SFD (purple packet)
Address (yellow packet)
EtherType (yellow packet)
IP packet (purple packet)
Data (cyan packet)
IPv4 packet (pink packet)
TCP packet (white packet)
Frame Check Sequence (yellow packet)
Error (red packet)
End of packet (red bar)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
The Protocol Decode Results Table provides a time-stamped, tabular view of all captured packets on the Automotive Ethernet (100BASE-T1) bus.

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Searching on a specific data pattern on the Automotive Ethernet (100BASE-T1) bus and automatically searching on Start of Frame.

8b10b Characteristics
Bus setup options
Characteristic Description
8b10b Sources
(Strobe and Data)
Analog Channels
Digital Channels
Active Math Channels
Active Reference Channels
Thresholds Per-Channel Thresholds
Recommended Probing Differential
Formats Available Hex
Binary
Symbolic

 

Display modes
Characteristic Description
Bus Bus Only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Results Table Decoded packet data in a tabular view

 

Bus search options
Characteristic Description
Search On Symbols [Format:8bit,10bit&symbol]
Errors

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate 1 Tbits/sec
Decode Display Control Symbol (yellow packet)
Data Symbol (cyan packet)
Error Handling Invalid Symbols
Running Disparity (6 bit and 4 bit)

 


3 4 5 6Series MSO Serial Bus Analysis Datasheet
Searching on a specific data symbol in symbol format on a 8b10b bus


3 4 5 6Series MSO Serial Bus Analysis Datasheet
The Protocol Decode results table provides time-stamped, tabular view of all captured packets on a 8b10b bus

NRZ Characteristics
Bus setup options
Characteristic Description
NRZ Source(s) Analog Channels
Digital Channels
Active Math Channels
Active Reference Channels
Thresholds Per-channel Thresholds
Recommended Probing Differential
Bit Order MSB First
LSB First
Polarity Normal
Invert
Formats Available Hex
Binary

 

Display modes
Characteristic Description
Bus Bus Only
Bus and Waveforms Simultaneous display of bus and digital waveforms.
Results Table Decoded packet data in a tabular view

 

Bus search options
Characteristic Description
Search On Data Bytes [Maximum 5]

 

Bus decode
Characteristic Description
Maximum Clock/Data Rate 1Gbits/sec
Decode Display Data (cyan packet)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Searching on a specific data symbol in symbol format in the NRZ bus


3 4 5 6Series MSO Serial Bus Analysis Datasheet
The Protocol Decode results table provides time-stamped, tabular view of all captured packets on the NRZ bus

 

PSI5 characteristics
Bus setup options
Characteristic Description
PSI5 Sources Analog channels
Digital channels
Active Math channels
Active Reference channels
Thresholds Per-channel thresholds
Recommended Probing Sensor to ECU Current probe with minimum current rating of less than 50mA - TCP2020, TCP202A
ECU to Sensor Differential Voltage probe - TDP1000, TDP1500, and TAP1500
Direction ECU to Sensor
Sensor to ECU
Direction -Sensor to ECUMode Slow (83.3 kbps)
Standard (125 kbps)
Fast (189 kbps)
Data A 10 - 24 bits
Data B 0 - 12 bits
Frame Control 0 - 4 bits
Status 0 - 3 bits
Direction - ECU to SensorSync Bit Period 1 us to 300 us
Sync Mode Pulse Width
Tooth Gap
Data Format Nibble
Byte
Decode Format Hex
Binary
Mixed Hex
Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous displays bus and digital waveforms
Results Table Decoded packet data in a tabular view
Bus search options
Characteristic Description
Mark On Direction - Sensor to ECU Start [Start of packet]
Status
Data [Region B and Region A]
Block ID
Sensor Status [5 different status]
Errors [Parity CRC and any]
Direction - ECU to Sensor Start [Start of packet]
Status
Data [4 or 8 bits]
Function Code
Sensor Address
Register Address
CRC Error
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Note: Bus Search option is depend on the direction in Bus Configuration.
Bus decode
Characteristic Description
Decode Display Direction -Sensor to ECU PacketsMessage Field (Yellow Field)
Status (Yellow Field)
Frame Control (Yellow Field)
Data B (Cyan Field)
Data A (Cyan Field)
Parity or CRC (Purple Field)
Direction - ECU to Sensor PacketsSensor Address (Yellow Field)
Function Code (Yellow Field)
Register Address (Yellow Field)
Data (Cyan Field)
CRC (Purple Field)
Error Type Parity
CRC
Response Code (Sensor to ECU)

3 4 5 6Series MSO Serial Bus Analysis Datasheet
PSI5 Search configuration


3 4 5 6Series MSO Serial Bus Analysis Datasheet
PSI5 Results table

MDIO Characteristics
Bus setup options
Characteristic Description
MDIO Sources (Clock, Data) Analog channels
Digital channels
Active Math channels
Active Reference channels
Thresholds Pre-channel thresholds
Recommended Probing Single-ended
Formats Available Hex
Binary
Mixed Hex
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Bus configuration
Bus search options
Characteristic Description
Search On Start Packet
OpCode
Physical Address
Register Address
Data
Error: Any, OpCode Error, Device Type Error
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Search configuration
Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Result Table Decoded packet data in tabular view
Bus decode
Characteristic Description
Maximum Clock/Data Rate Maximum frequency of up to 2.5 MHz
Decode Display Start Packet (Green)
Clause (Green)
OpCode (Yellow)
Physical Address (Yellow)
Register Address (Yellow)
Device Type (Yellow)
Data/Address (Cyan)
Error: Any, OpCode Error,
Device Type Error (Red)

3 4 5 6Series MSO Serial Bus Analysis Datasheet

SVID characteristics
Bus setup options
Characteristic Description
SVID Sources (Clock, Data, Alert) Analog channels
Digital channels
Active Math channels
Active Reference channels
Thresholds Pre-channel thresholds
Recommended Probing Single-ended
Formats Available Hex
Binary
Mixed Hex
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Bus configuration
Bus search options
Characteristic Description
Search On Start
Slave Address
Command
Payload: Master, Slave, Either
Errors: Any, Missing Ack, Parity
End
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Search configuration
Display modes
Characteristic Description
Bus Bus only
Bus and Waveforms Simultaneous display of bus and digital waveforms
Result Table Decoded packet data in tabular view
Bus decode
Characteristic Description
Maximum Clock/Data Rate Maximum frequency of 26.25 MHz
Decode Display Start (Green)
Slave Address (Yellow)
Command (Yellow)
Master Payload (Cyan)
Master Parity (Purple)
End (Purple)
Turnaround (Purple)
Ack (Purple)
Slave Payload (Cyan)
Slave Parity (Purple)

3 4 5 6Series MSO Serial Bus Analysis Datasheet

e-USB2
Bus setup options
Characteristic Description
Source(s) Analog channels
Digital channels(single-ended)
Active Math channels
Active Reference channels
Thresholds Pre-channel thresholds
Speeds Speed High Speed (480 Mb/s)
Full Speed (12 Mb/s)
Low Speed (1.5 Mb/s)
Recommended Probing, HS, LS, and FS Single-ended [Active Single Ended TAP1500]
Formats Available Mixed Hex
Hex
Binary
Mixed ASCII
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Bus configuration
Bus search options
Characteristic Description
Search On Characteristic Description
Search On Sync
Reset
Suspend
Resume/Wake
Connect
Control Message
Port Reset
Port Configuration
Device Chirp
Host Chirp
End of Packet
Token (address) Packet
Data Packet
Handshake Packet: ACK, NAK, STALL, NYET (HS only)
Special Packet: PRE (FS only), ERR, SPLIT, PING
Reserved
Error: PID check, CRC5 or CRC16, Bit stuffing (LS and FS only)
3 4 5 6Series MSO Serial Bus Analysis Datasheet
Search configuration
Bus decode
Characteristic Description
Decode Display Start of packet (green bar)
Sync (green packet)
PID (yellow packet)
Token (address) (yellow packet)
Data (cyan packet)
CRC (purple packet)
Error (red packet)
End of packet (red bar)
Control Message (Yellow packet)
Zeros (Blue packet)
Ack (Purple packet)
Port Reset (Red Bar)
Port Configuration(Green Bar)
Connect (Green Bar)
Resume/Wake(Green Bar)
Device Chirp(Green Bar)
Host Chirp (Green Bar)
End Of reset(Red Bar)
Results & other features
Characteristic Description
Table view
* Depends on the Model
View more than 10000* points
Save Save Result table as CSV
Sessions Save sessions of your protocol setup
Simultaneous Buses
* Depends on the Model
Load multiple Buses simultaneously*
Upcoming Future addition Timing Measurements for Protocols
Search Table Displays the Search hits along with Delta time difference between hits

3 4 5 6Series MSO Serial Bus Analysis Datasheet
Results table with decoded waveform

Ordering information

To add to an instrument at purchase
Serial bus type 3 Series MDO Option 4 Series MSO Option 5 Series MSO Option 6 Series MSO Option Description
MIL-STD-1553, ARINC 429  3-SRAERO 4-SRAERO 5-SRAERO 6-SRAERO Aerospace Serial Triggering and Analysis (MIL-STD-1553, ARINC 429). Enables triggering on packet-level information on MIL-STD-1553 and ARINC 429 buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
I2S, LJ, RJ, TDM 3-SRAUDIO 4-SRAUDIO 5-SRAUDIO 6-SRAUDIO Audio Serial Triggering and Analysis (I2S, LJ, RJ, TDM). Enables triggering on packet-level information on serial audio buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
8b10b N/A N/A 5-SR8B10B 5-SR8B10B 8B10B Serial Decoding and Analysis. Enables decoding and searching the packet-level information on buses with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information. Finds and displays parity error if found in 4-bit or 6-bit for the 10-bit symbol in 8b10b.
NRZ N/A 4-SRNRZ 5-SRNRZ 6-SRNRZ NRZ Serial Decoding and Analysis. Enables decoding and searching the packet-level information on buses with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information. Variants like NRZ-I, NRZ-M, NRZ-S, and NRZ-C are not supported currently. Supports only NRZ with normal and inverted polarity with Bit Order (MSB or LSB First).
CAN, CAN FD, LIN, FlexRay 3-SRAUTO 4-SRAUTO 5-SRAUTO 6-SRAUTO Automotive Serial Triggering and Analysis (CAN, CAN FD, LIN, FlexRay). Enables triggering on packet-level information on CAN/CAN FD/LIN/FlexRay buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
Automotive 100BASE-T1 N/A N/A 5-SRAUTOEN1 6-SRAUTOEN1 100BASE-T1 Automotive Ethernet serial analysis.
SENT N/A 4-SRAUTOSEN 5-SRAUTOSEN 6-SRAUTOSEN Automotive Sensor Serial Triggering and Analysis (SENT). Enables triggering on packet-level information on SENT buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
RS-232/422/485, UART 3-SRCOMP 4-SRCOMP 5-SRCOMP 6-SRCOMP Computer Serial Triggering and Analysis (RS-232, RS-422, RS-485, UART). Enables triggering on packet-level information on RS-232/422/485 and UART buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
I 2C, SPI 3-SREMBD 4-SREMBD 5-SREMBD 6-SREMBD Embedded Serial Triggering and Analysis (I2C, SPI). Enables triggering on packet-level information on I2C and SPI buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
Ethernet N/A 4-SRENET 5-SRENET 6-SRENET Ethernet Serial Triggering and Analysis (10BASE-T, 100BASE-T). Enables triggering on packet-level information on Ethernet buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
I3C N/A 4-SRI3C 5-SRI3C 6-SRI3C I3C Serial Decoding and Analysis. Enables decoding and searching on packet-level information on MIPI I3C buses with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
SPMI N/A 4-SRPM 5-SRPM 6-SRPM Power Management Serial Triggering and Analysis (SPMI). Enables triggering on packet-level information on SPMI buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
Spacewire N/A 4-SRSPACEWIRE 5-SRSPACEWIRE 6-SRSPACEWIRE Spacewire serial analysis. Enables decoding and analysis on Spacewire buses.
USB 2.0  3-SRUSB2 4-SRUSB2 5-SRUSB2 6-SRUSB2 USB 2.0 Serial Triggering and Analysis (LS, FS, HS). Enables triggering on packet-level information on USB 2.0 buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
Serial options bundle 3-BND N/A N/A N/A Adds all serial analysis options and the power analysis option available for an instrument.
PSI5 N/A 4-SRPSI5 5-SRPSI5 6-SRPSI5 PSI5 Serial Decoding(v1.3 and 2.1) and analysis. Enables decoding and Search Packet level information with analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information.
MDIO N/A LIC4-SRMDIO LIC5-SRMDIO LIC6-SRMDIO License; MDIO Protocol Decoder and Search, No Hardware Trigger; Node locked
SVID N/A LIC4-SRSVID LIC5-SRSVID LIC6-SRSVID License; SVID Protocol Decoder and Search, No Hardware Trigger; Node locked
e-USB2 N/A LIC4-SREUSB2 LIC5-SREUSB2 LIC6-SREUSB2 License; eUSB2 Protocol Decoder and Search; Node locked
To upgrade an already purchased instrument
Serial bus 13 Series MDO Node-Locked License 24 Series MSO Node-Locked/Floating License 5 Series MSO Node-Locked/Floating License 6 Series MSO Node-Locked/Floating License
MIL-STD-1553, ARINC 429  SUP3 SRAERO SUP4-SRAERO SUP4-SRAERO-FL SUP5-SRAERO SUP5-SRAERO-FL SUP6-SRAERO SUP6-SRAERO-FL
I2S, LJ, RJ, TDM SUP3 SRAUDIO SUP4-SRAUDIO SUP4-SRAUDIO-FL SUP5-SRAUDIO SUP5-SRAUDIO-FL SUP6-SRAUDIO SUP6-SRAUDIO-FL
CAN, CAN FD, LIN, FlexRay SUP3 SRAUTO SUP4-SRAUTO SUP4-SRAUTO-FL SUP5-SRAUTO SUP5-SRAUTO-FL SUP6-SRAUTO SUP6-SRAUTO-FL
8B10B N/A N/A SUP5-SR8B10B
SUP5-SR8B10B-FL
SUP6-SR8B10B
SUP6-SR8B10B-FL
NRZ N/A SUP4-SRNRZ
SUP4-SRNRZ-FL
SUP5-SRNRZ
SUP5-SRNRZ-FL
SUP6-SRNRZ
SUP6-SRNRZ-FL
100BASE-T1 Automotive Ethernet N/A N/A SUP5-SRAUTOEN1 SUP5-SRAUTOEN1-FL SUP6-SRAUTOEN1 SUP6-SRAUTOEN1-FL
SENT N/A SUP4-SRAUTOSEN SUP4-SRAUTOSEN-FL SUP5-SRAUTOSEN SUP5-SRAUTOSEN-FL SUP6-SRAUTOSEN SUP6-SRAUTOSEN-FL
RS-232/422/485, UART SUP3 SRCOMP SUP4-SRCOMP SUP4-SRCOMP-FL SUP5-SRCOMP SUP5-SRCOMP-FL SUP6-SRCOMP SUP6-SRCOMP-FL
I2C, SPI SUP3 SREMBD SUP4-SREMBD SUP4-SREMBD-FL SUP5-SREMBD SUP5-SREMBD-FL SUP6-SREMBD SUP6-SREMBD-FL
Ethernet N/A SUP4-SRENET SUP4-SRENET-FL SUP5-SRENET SUP5-SRENET-FL SUP6-SRENET SUP6-SRENET-FL
I3C N/A SUP4-SRI3C SUP4-SRI3C-FL SUP5-SRI3C SUP5-SRI3C-FL SUP6-SRI3C SUP6-SRI3C-FL
SPMI N/A SUP4-SRPM SUP4-SRPM-FL SUP5-SRPM SUP5-SRPM-FL SUP6-SRPM SUP6-SRPM-FL
Spacewire N/A SUP4-SRSPACEWIRE SUP4-SRSPACEWIRE SUP5-SRSPACEWIRE SUP5-SRSPACEWIRE-FL SUP6-SRSPACEWIRE SUP6-SRSPACEWIRE-FL
USB 2.0  SUP3 SRUSB2 SUP4-SRUSB2 SUP4-SRUSB2-FL SUP5-SRUSB2 SUP5-SRUSB2-FL SUP6-SRUSB2 SUP6-SRUSB2-FL
Serial analysis bundle 3SUP3 BND N/A N/A N/A
PSI5 N/A SUP4-SRPSI5 SUP4-SRPSI5-FL SUP5-SRPSI5 SUP5-SRPSI5-FL SUP6-SRPSI5 SUP6-SRPSI5-FL
MDIO N/A SUP4-SRMDIO SUP4-SRMDIO-FL SUP5-SRMDIO SUP5-SRMDIO-FL SUP6-SRMDIO SUP6-SRMDIO-FL
SVID N/A SUP4-SRSVID SUP4-SRSVID-FL SUP5-SRSVID SUP5-SRSVID-FL SUP6-SRSVID SUP6-SRSVID-FL
e-USB2 N/A SUP4-SREUSB2 SUP4-SREUSB2-FL SUP5-SREUSB2 SUP5-SREUSB2-FL SUP6-SREUSB2 SUP6-SREUSB2-FL

 

 

1Software is supplied with the instrument firmware. Always download and install the latest version of the firmware. Option documentation is part of the application Help.

23 Series MDO option license names do not have a dash in the option number.

3All serial bus and power analysis options that are available for an instrument.

Recommended probes
Please refer to www.tek.com/probes for further information on the recommended models of probes and any necessary probe adapters.